Passtrough AMD Ryzen 7 5825U
Hi everyone, I recently bought a small home server and installed Proxmox. On one of the VMs (Debian), I’m running Jellyfin and I want to passthrough the AMD Ryzen 7 5825U IGPU. The Wi-Fi passthrough...
View ArticleIntel E810-C 100G + Dell S532F-ON = Headaches
Hello Proxmox Community! We are attempting to upgrade the core networking from 10Gb to 100Gb with a Dell S5232F at the helm for the cluster and a Dell S5248F for all of our network access switches to...
View ArticleVM-Filesystem defekt nach Netzwerkausfall zu Ceph
Hallo Zusammen, ich betreibe einen Proxmox-Cluster und einen Ceph-Cluster. Es gibt drei Netzwerke dafür: Proxmox-Cluster-Intern (nur Proxmox-Nodes) Ceph-Cluster-Intern (nur Ceph-Nodes)...
View ArticleClik here to view.
Proxmox ceph upgrade problems experienced
Hi, Ceph pacific (16.2.13) to quincy 17.2.6 During the quincy upgrade process from ceph pacific, we could not upgrade our osd disks while we were upgrading 17.2.6 in monitor, manager and meta. Since I...
View ArticleAyuda con puertos
Hola buenos días alguien me podría dar una guía o explicar cómo se hace para abrir un mismo puerto en varios vps, tengo proxmox instalado y mis maquinas virtuales configuradas con IP lan , todas tienen...
View ArticleClik here to view.
Win Srv 2022 Guest does not properly shut down during backup.
I have a monthly backup of all VMs in my homelab. The backup works but every month one particular VM (Windows Server 2022, 128G Drive C, 4T Drive D, 16G RAM) hangs during the restart process and...
View ArticleClik here to view.
EXT4-fs error
Hello, Every few days or hours my proxmox device crashes. Everytime I reboot the system it works for a while. I never had it connected to a monitor so I could never see any errors, until today. Today...
View ArticleBackup Performance - would multithread improve it?
Hello, We run our PBS and have mounted RBD block devices from a Ceph cluster. The Ceph cluster consists of 12, 14, and 16 enterprise HDDs (not SSDs), making it relatively cheap, large, but somewhat...
View ArticleVLAN interfaces not selectable in VM NIC Config
I'm working on deploying a 7 node Proxmox VE cluster. We have several other clusters running PVE 6/7. As I'm working on configuring the network, I'm used to configuring it like this: Code: auto lo...
View Articlepveproxy - is disabling tls or moving its port possible?
I'm working with a new PVE install over top of Debian. I want to disable tls and connect to pveproxy over vanilla http to avoid exposing PVE's UI to the internet. I found this instruction which speaks...
View ArticlePCIe Support in 8er Version klappt nicht
Hallo Leute, ich versuche gerade verzweifelt von Proxmox V7 auf V8 umzusteigen, bekomme aber das PCIe Passtrough nicht mehr hin. In der 7er klappt es mit den gängigen Anleitungen einwandfrei, aber bei...
View ArticleProxmox cluster 4 node and dell em5024 storage
Dell r650 servers with fibre channel adapter, dell em5024 storage system, configured a proxmox cluster of 4 nodes. The disks are visible twice in the nodes because they are connected to two...
View Article2FA authentication
I would like to activate 2FA for the WebGUI / App (not per SSH). However, access to a server from the internal network should work without 2FA. Is that possible and if so how?
View ArticleHDD never spin down
Hi, I have a Proxmox server (5.2.1) with the config below : - Xeon E5 2650 V2 - 16Gb Ram ECC - 120 GB SSD (KINGSTON SV300S3) - 2x2To HDD (Hitachi HUS72403 and TOSHIBA DT01ACA3) The proxmox server is...
View ArticleOPenVPN Access Server
I am extremly new to Proxmox and ran into the issuie where I installed OpenVPN in an ubuntu VM and now cant access the webinterface trhought the ip addres it gave me in the command line. while it...
View ArticleCannot run LXC after putting some files on it. Also, a VM got a io-error
Hello! I was running a Home Manager installation on a VM and a Jellyfin installation on a LXC. Now the VM launches, but there's a yellow triangle next to it, the system states there's an io-error. The...
View ArticleUpdating to 8.3.3 broke some things
So I went to update my PVE 8.3.2 last night and ran into this issue and I've now hit a wall and would love some assistance. pve-cluster, pve-firewall and pve-fstab stopped responding after rebooting...
View ArticleClik here to view.
ZSTD-compressed data is corrupt
Hello, after restarting my Proxmox, an error message appears as shown. I am using Proxomox 8.3.3, this is the first time a problem like this has appeared, previously using version 8.1 / 8.2 safely no...
View ArticleDisk Layout - New Install
Hi. Will be setting up proxmox (first time) soon for a homelab with TrueNASbeing one of the first VMs being created. Was wondering what the ideal disk layout would be given the following drives: 5x 1TB...
View ArticleSlow write performance in Rocky/RHEL VMs
Hello everyone, at my work we are migrating from ESXi to Proxmox. After having migrated about 25 VMs with Rocky and having created about 10 more VMs, I have realized that the writing speed is being...
View Article